Sprinkle the waterwheel pump does not absorb water or no water, to a "Overlord hard strike", the driver did two brothers to the emergency, "brush", it can only wait helplessly suffer "shabu", and Should not be reconciled, that You have to keep in mind the following few tricks in mind! For more information about the sprinkler, please consult Xiamen Xigong Chusheng (Hubei) Special Automobile Manufacturing Co., Ltd. Sales Department: 0722-7504111 Â Company official website :
Coupling
Tubing and casing couplings are the joining of two short length pipe, mainly used for the connection and repair of oil pipe and downhole tools
Tubing and couplings thread types : Non-upset thread(NU), External- upset thread(EU);
Casing and couplings thread types: Long-round thread(LC), Short-round thread(SC), buttress thread(BC)
Grade: K55,J55,N80-1,N80Q,L80-1,P110,etc.
Pup joint
Tubing and casing pup joints are machined according to the latest version of API SPEC 5CT. The steel grade includes J55,K55,N80-1,N80Q,L80-1,P110,etc. There are two types of thread widely used in tubing pup joint namely Non-upset thread(NU), External- upset thread(EU);
Casing and couplings thread types: Long-round thread(LC), Short-round thread(SC), buttress thread(BC).
Our testing and inspection method system is complete, using a whole set of thread instrument to inspect taper, pitch, tooth, height, tooth type,etc. The products have passed the identification of china petroleum pipeline. Quality supervision ,inspection and testing center and gained the unanimous praise from the customers.
Crossover
Crossover coupling any size ,length ,grade and weight is available on customer request.
X-Over Coupling,X-Over Crossover,Oil Well Tubing,Tubing Pipe Coupling Henan Dongfanglong Machine Manufacture Co., Ltd , https://www.eastlongmachine.com
If the sprinkler does not absorb water, follow the steps below to diagnose quickly:
The first step is to check the switch. First check whether the water pump outlet and outlet switch of the sprinkler pump is turned on. The water pump for the sprinkler is a self-priming pump. When the water is used for the first time, the water should be poured.
The second step is to check the filter. When the sprinkling of the water pump is not smooth, check the front section of the suction pipe for debris blocking the water inlet, and then check the inlet pipe line by stage to see if there is a leakage failure.
The third step is to check the degree of vacuum. The height of the water pump used for ordinary sprinklers should be less than 5 meters. Then check whether the water pump oil seal of the sprinkler is damaged or not. The leakage of the pump shaft will affect the vacuum level and the seal should be replaced. When the sprinkler engine speed is too low to reach the required vacuum, adjust the throttle to make the speed at about 1700 rev / min, the engine speed varies depending on the gearbox.
The fourth step is to check the power take off. Check if the sprinkler power take-off is working, and the power take-off and the drive shaft can cause the water pump to stop working.
The fifth step to listen to abnormal noise. Check to see if the speed of the sprinkler's water pump is normal and pay attention to whether there is any abnormal sound or not and determine if the pump cannot rotate properly due to debris. However, it is important to note that the pump cannot be idling for a long time during the test. Otherwise, the service life of the pump will be shortened due to the high temperature of the pump.
If the water pump of the sprinkler does not discharge water, after the detailed inspection according to the above steps, if the fault can not be eliminated, then check whether the outlet filter or the pump body is blocked due to a long time when the uncleaned water tank is too dirty.
It's also important to develop good habits. The water irrigation should be cleaned regularly. In winter, after using the watering vehicle, the water tank and the water in the pump body must be drained to prevent freezing and cracking of the tank body and the water pump.
How to do if the sprinkler pump does not absorb water