If the camera does not need to be rotated to monitor only a certain position, only the camera bracket can be used. Ordinary camera brackets are simple to install, inexpensive, and varied. Resin Ribbon,Resin Ribbon Price,Label Printer Ribbon,Wax Thermal Transfer Ribbon Guangdong Shuangma Technology Co., Ltd. , https://www.soonmarkprinter.com
Ordinary brackets are short, long, straight, and bent, and different models are selected according to different requirements. The outdoor support mainly considers whether the load capacity meets the requirements, and then there is the installation position, because in practice we have found that many outdoor cameras are installed in special locations, some are installed on poles, some stand on tower cranes, and some are installed on iron. On the shelf... Due to various reasons, existing brackets may be difficult to meet requirements and require additional processing or improvement, and no more will be said here.
The installation height of the indoor camera is 2.5 to 5m, and the outdoor is 3.5 to 10m; the elevator car is installed on the top of the elevator car, and it is diagonally opposite to the elevator operator, and the optical axis of the camera and the two walls and the ceiling of the elevator. It's 45 degrees.
Camera installation precautions
The use of the camera is very simple. Normally, it is only necessary to properly install the lens, connect the signal cable, and turn on the power to work. However, in actual use, if you do not install the lens correctly and adjust the camera and lens status, you may not achieve the expected results. Should pay attention to the lens and camera interface, whether it is a C-type interface or a CS-type interface (this must be remembered, otherwise it will most likely damage the camera's CCD chip when the C-type lens is directly screwed onto the CS interface camera).
When installing the lens, first remove the protective cover of the camera and the lens, then gently screw the lens into the lens connector of the camera and put it into place. For auto iris lenses, the lens control line should also be connected to the camera's auto iris interface. For motorized two-variable or three-variable lenses, as long as the lens is rotated into position, it is not necessary to correct its equilibrium state (only after After the focus adjustment is completed, it is necessary to finally correct its equilibrium state).
Adjust lens aperture and focus
Turn off the electronic shutter and back light compensation switch on the camera to align the camera with the scene to be monitored and adjust the lens aperture and focus ring to optimize the image on the monitor. If you use the camera in a place with a large variation in illumination, it is best to connect the auto iris lens and set the camera's electronic shutter switch to OFF. If the manual iris is selected, the camera's electronic shutter switch should be turned ON, and when the application site is brightest (maximum ambient light), the lens aperture should be as large as possible and still make the image the best (can not make the image too much White and overloaded, the lens is adjusted. Put on the protective cover and put on the bracket
In the above adjustment process, if you do not pay attention to when the light is bright, the aperture of the lens should be as large as possible, but it is relatively small, the electronic shutter of the camera will be automatically adjusted at a low speed, so it can still be formed on the monitor. Good image; but when the light is dimmed, because the aperture of the lens is relatively small, and the electronic shutter is already at the slowest (1/50s), the imaging at this time may be dim.
Camera installation method:
first step
Take out the bracket and prepare the tools and parts: plug, screw, screwdriver, hammer, electric drill, and other necessary tools; check the size of the plug and tapping screws according to the pre-determined mounting position; try the bracket screws and Whether the screw base of the camera base is appropriate, whether the pre-embedded pipeline interface is handled well, and whether the test cable is unblocked, and then enter the installation procedure after being ready.
Second step
Take out the camera and lens, according to the pre-determined camera lens model and specifications, carefully install the lens (infrared camera and integrated camera does not need to install the lens), be careful not to touch the lens and CCD (marked part of the figure), confirm the fixed After firm, turn on the power, connect the host or use a monitor, small TV, etc. to adjust the aperture.
The third step is to take out the brackets, plugs, screws, screwdrivers, hammers, drills and other tools, and install the brackets according to the predetermined position. After the inspection is firm, install the camera in the appointed direction; (Before installing the bracket, check the power in the place of installation to obtain a more reasonable monitoring effect.)
the fourth step
If there is a lot of dust in the outdoors or in the room, install the camera shroud. After the second step, install the shroud directly from here.
1. Open the shield cover and tailgate;
2. Pull out the fixed metal plate and fix the camera;
3, the power adapter into the shield;
4. Reset the upper cover plate and the rear baffle, straighten the cable, fix it, and install it on the bracket.
the fifth step
Insert the BNC plug of the soldered video cable into the socket of the video cable (align the two fixing posts of the video socket of the camera with the two notches of the plug, and turn it clockwise after inserting it). Make sure that the BNC connector is securely attached and in good contact.
Step 6
Plug the power adapter's power output plug into the monitoring camera's power jack and confirm the firmness (note the camera's power requirements: Normal gun camera uses 500-800mA 12V power supply, infrared camera uses 1000-2000mA 12V power supply, please refer to the product instructions to select suitable The product).
Step 7
Connect the camera to the mobile video server of Joy Communications Technology Co., Ltd. Connect signal sources and networks.
Step 8
According to your own mobile phone model, the corresponding mobile phone video surveillance mobile client is suitable for debugging the frame rate and stream according to your network environment. At this point, you can smoothly use the mobile phone to pass through the world.
Installation tutorial, eight steps to install mobile video surveillance