If the oil temperature is too high, the screw air compressor will cause thermal expansion of the main and slave rotors due to the rising temperature, which will cause the gap to decrease and the oil film to become thinner. If not controlled, it will cause the rotor end face to rub against the exhaust seat. This produces a vicious cycle in which the impurities in the oil increase and the temperature rises. For example, when the temperature rise is 100 °C, the rotor is ductile cast iron, the coefficient of linear expansion α is 10×10-6/°C, and the effective length of the rotor is 425 mm, then the rotor elongation L is 0.425 mm. During installation, the clearance between the rotor and the exhaust seat end is only 0.08 ~ 0.12mm, and the clearance between the end face of the air inlet is 0.48 ~ 1.02mm. The design requires that the exhaust temperature does not exceed 125 ° C. If the temperature is close to the upper limit and the rotor and bearing clearance Improper adjustment can easily lead to wear of the cylinder and rotor end faces. Damage of the bearing In this accident, the bearing raceway was severely worn and peeled off, resulting in overheating burns. As a result, the clearance is increased and the precision is lowered, eventually leading to discoloration of the exhaust seat support and the journal and deep marks. Causes: First, the carbon blockage of the copper tube, resulting in poor bearing lubrication, temperature rise; second, because the bearing assembly does not meet the requirements. The influence of lubricating oil also found that the anti-embroidery turbine oil used in the screw has deteriorated and aged during the disintegration process. There is carbon deposit and more impurities, which leads to the pipeline is not very smooth, and the temperature rises too fast. First, the air filter and oil filter are not cleaned regularly; the second is due to the poor quality of the rust-proof turbine oil used. The minimum clearance between the rotor and the body is only between 0.07 and 0.11mm. If there is too much debris in the body, it will cause the body to be injured or bite the host and the whole machine will be scrapped. Assembly and improvement measures Improvements and precautions for the lubrication system Improvements Lubrication in the compressor not only reduces the friction and wear of the machine, but also acts as a seal, cooling and noise reduction. Good lubrication conditions are long-term reliability of the compressor. An important guarantee of work. (1) Increasing the temperature controller The original design is to install the temperature controller on the Class II oil separator in order to control the exhaust temperature. The main temperature is only the block temperature meter. The temperature in the oil separator is due to the heat dissipation through the pipeline. Below the host temperature, this causes the temperature controller to not control the oil temperature well, and the temperature gauge on the main unit is not easy to observe. A temperature controller can be added to the main unit to control the oil temperature. (2) Oil pump modified screw air compressor The original design oil pump is a cycloidal pump with low oil pressure, poor cooling effect and difficult to repair. Our mine is now changed to CB140E gear pump, the rated pressure is 2.5MPa, after several years of good use, but the oil pressure is not stable enough and large, need to add another overflow valve to adjust.
We have got CE certificate from 2015. We make can manufacture various types of high mast with lifting system for stadium highway parking lot and etc.
Our firm introduced whole set of good-sized numerical control hydraulic
folding equipment(1280/16000) as well as equipped with a series of
good-sized professional equipments of armor plate-flatted machine,
lengthways cut machine, numerical control cut machine, auto-closed up
machine, auto-arc-weld machine, hydraulic redressing straight machine,
etc. The firm produces all sorts of conical, pyramidal, cylindrical
steel poles with production range of dia 50mm-2250mm, thickness
1mm-25mm, once taking shape 16000mm long, and large-scale steel
components. The firm also is equipped with a multicolor-spayed
pipelining. At the meantime, for better service to the clients, our firm
founded a branch com. The Yixing Jinlei Lighting Installation Com,
which offers clients a succession of service from design to manufacture
and fixing.
Steel Lighting Pole High Mast,30m High Mast Pole, High Mast pole for stadium Jiangsu Xinjinlei Steel Industry Co., Ltd. , https://www.jinleisteelpole.com
The latest bar compressor problem analysis and change initiatives